Try same settings as me, try with high pl
Hola tengo un caso parecido con una 2060s como lograste subir la potencia mhs, si es el procesador que influye en el OC ?
Processor does not influence
Hello Marcio, I ended up selling this 2060s, because I couldn’t solve this problem. I put a 1080 TI in its place, I’m quite satisfied so far. Thank you very much for your suggestion.
I saw that the ones with Samsung memory can go to 48 MHs → The best card for mining? nVidia 2060 super is just amazing! - YouTube
Sadly, Micron is limited to 42 (best case scenario).
I have GALAX RTX 2060 Super with Micron memories, I tried tons of combinations and couldn’t go further of 37,5 MHs in Hive and 38,5 MHs in Windows (with afterburner). But I always tried 130 Power Limit and different values in Memory and Core, the GPU always draws around 90 W.
Then I tried what MarcioS suggested and used 180+ PL, and that makes the trick. It seems that with a low PL the GPU is unable to draw more power so you are limited to use higher Memory values. The max factory PL for my card is 200W so I think not going further than that may be safe. Anyway now the GPU is mining 42,2 MHS and using 112W, it never reaches the PL value.
My actual overclocking in HiveOS is:
Core: -400
Memory: 1800
Power Limit: 190
MHs: 42,2
May be that playing a bit with this values I can get some extra MHs, but increasing the PL makes the huge difference.
The information in this post was very useful, thank you all !
Привет тебе и всем владельцам 2060 супер )
Решил проблему малого значение настройкой напряжения открыл настройки Курвы) и выставил напряжение 1100 все линии , значение памяти +1250 , повер лимит 114
и с 38 стало 44
How did you do that?
Undervolting try, it helped me, with 38 I did 45
1 Like
I have a 2060 Super with Micro memory as well that is running in the 38 M/h range. After messing with this thing for about a hour within HiveOS, I think I see what is going on, but unsure how to resolve. I can core lock it by setting core to 1050 (really, it doesn’t seem to matter what you set the core at). I can get to 40 M/h if I set the memory to 1200. I have PL set to 184 (max on my card). With these settings I get 1050 MHz core and 7400 MHz on memory using 100W. If I increase memory to 1250 or anything above 1200, I get throttling on my card with a reason of PowerLimit. When this happens, my core drops to the 850-900 MHz range and the M/h drops. If I set memory back to 1200 (not going above 7400 MHz), the throttling goes away and I get 40 M/h again.
This would lead me to believe that this is most likely a power level setting within the BIOS once you cross over 7400 MHz memory clock. I have no idea how to go about fixing that within HiveOS though.
2 Likes
Hi
When you set as that stable, they will get rejected share or invalid share.
I run 72h or more with core 1100, mem 2100 (MSI 2060S) and get 43.5Mh/s (micron memory); Gigabyte is 44.1Mh and Nvidia is 44.8Mh that without any errors.
You can reset all if you want
Hi
You can try with this overclocking on HiveOS that not adjust on MSI Afterburner . After that waitting (30 seconds) and reboot your rig
Good luck!
Hi, I always have different shows, not stable balls, I can’t understand what the reason is, farmed both on 43 and her 44 and 45, always more than 2% of the rejected
me pasa exactamente lo mismo :C
Thanks man, works like a charm (Asus Dual OC), @42.07 though
