Asus Dual v2 3060 ti
Trex miner with :
“lhr-tune”:“75.5,75.5,75.5,75.5,75.5”
“lhr-autotune-step-size”: “0.1”
“lhr-autotune-interval”: “10”
0.5 steps for LHR are too big for me and cards settled with this OC very nice by 0.1.
3 Likes
Hey team,
This my OC set up (stable) with lower PL.
Can do more 1or 3 more mh/s but for 10 20 watts more … not worth it.
I am with nb miner
Any comments for improvement are welcome
Hi.
This is my first rig, and I can’t get higher than 32.9MH/s with my 3060 ti Gigabyte Aorus.
I see lot of you reaching 45 to 55, but even using the same overclocking setting, I don’t get better values.
Is there anything specific to chenge on my side?
Hi Loïc,
For me the power used by your card is not sufficient
(101watt)
I use also nbminer which is good if you have LHR card
If you have an lhr card the Max you can reach is 45mh s with 130 watts.
Try this settings with NB miner
Cc -500
MC 1800
PL 120 -130w
In the mean time, I switched from Bminer to T-Rex, and I came to 46.66MH !
I didn’t think that the miner had such influence on the MH/s
So you think we cannot go more than that with a LHR?
As far as I Know you reach Max mh s for etherum with lhr.
How much power do you have for 46mh s ?
For me they are non lhr. With nb miner you use 75% of the card so with non lhr you should have 25% mh s more
Hello my friend.
I have one 3060ti LHR like yours:
Gainward RTX 3060 Ti Ghost 8GB
Hynix GDDR6 · 94.04.6B.00.F4 · PL 100 W, 200 W, 210
I did your settings but my hashrate is only 31 MH !!
could you please help me to fix it.
thanks
I don’t know which miner you are using, but I recommend you to use T-rex miner or gminer
Hi 
TON? 
I don’t know that 
In how far it’s more profitable than ETH? I just don’t find TON at whattomine.com
Greetings 
Hi Buddy,
I’ve done a little bit research and let one of my rigs mining TON. I’ve included the following screenshot for you: my ASUS 3060 Ti LHRs run perfectly at above 2 GH/s. Another question is: with all the tons of TON 
in my wallet… where do you change them into EUR / USD / BTC / ETH etc.??? OKEx? FTX?
Sincerly, GunZen
1 Like
It’s even better with less power: I think I finally found what I’ve looking for…
Core: 300 / Memory: 2300 / PL: 120
With less power a better hashrate! 
1 Like
try to use Lock Core Value… anything above 500 will be considered Lock Core and your consumption will drop further… start with 1000 and increase by 50 till you’ll find the sweat spot
Uhm, sorry, we were talking about TON with everything above 300 MHz Core the rig didn’t even started to work… I’ve already tried it with “the usual criminals” like 1500, 1000 and so on 
1 Like
Great job mate!
1 Like
Power limit is not useless on my LHR 60ti
Lhr cards act wierd.
I set my PL at 125 while using locked core at 1450, and i still get 44-45 mh.
If i remove power limit i get the same hashrate at higer watts. So why would i let it run no power limit.?
No, at Neocrypto for example you can just buy the coins, not sell… for me I found out to send the TONs to OKEx and sell them to USDT.