Bad cable? Network card on that motherboard known working? Network link indicator lights on? Could be anything but looks like it has no connection at all.
Ordered a new cable. The one we were using was a bit rough. What about the system not booting when the risers are plugged in?
hive isn’t seeing your card. If it isn’t a hardware issue (riser, cables, power, etc.), could be a bios problem. You could try running it without any overclocks, and cycling the power
Try nvidia-info to see if it detects your card.
=== GPU 6, 10:00.0 GeForce RTX 3060 Ti 7982 MB ===
Bios 94.04.46.00.D2, PCIE Link Gen 1, PCIE Link Width 1x
UUID GPU-1429493b-1682-aa85-ec1a-0687df02b12c, ROM flash: Supported
Power Limit: Min 100.0 W, Default 200.0 W, Max 200.0 W, Current 200.0 W
Frequency: GFXCore 1290 MHz, MEMCore 7400 MHz
Memory: Total 7982 MB, Used 5129 MB, Free 2852 MB, Hynix GDDR6
Utilization: GPU 100 %, MEM 100 %, Throttle: None
PSTATE P2, PWR 148.8 W, Temp 57 °C, Fan 36 %, RPM 1931 (35 %), RPM 1820 (35 %)
Else, you could use lspci. Your card should be listed somehow in the output
10:00.0 VGA compatible controller: NVIDIA GA104 [GeForce RTX 3060 Ti LHR] (rev a1)
10:00.1 Audio device: NVIDIA GA104 High Definition Audio Controller (rev a1)
Tried it with the graphics card that came with the motherboard a 1050 and hiveos boots when that is plugged in but still doesn’t detect the GPU. The fan is on and everything
Going to try and update the bios later
Quite likely settings in the BIOS related to PCI settings, etc.
Assuming you are providing correct and enough power to the GPU?
The 1050 gets it’s power from the board and the other 2 GPUs I had plugged in had 850w gold power supply. I would think that’s enough but idk??
How do you check the pci settings?
Typically an ASUS board will have them in in the BIOS under the advanced option.
Gaming boards tend to default into expecting your primary GPU being placed in the primary 16x slot natively.
In addition, you are running the onboard GPU, which implies that is in AUTO, or set by default.
If your intention is to mine with this board and GPUs on risers, you’ll likely need the follow set (CSM may not be an issue with your board):
Trying to find those settings on the bios after I updated it.
Anyone recommend another beginner motherboard? Around $100 hopefully
Have you put a 1060 in the PCI 16x slot(no risers) with the correct power cables in it, vs. the 1050?
Yes and it won’t boot with the card plugged in. I can boot it without a card plugged in and then add the card but then it won’t read the card
Now after the bios update it won’t boot with the 1050
After BIOS update, will it get through POST utilizing the iGPU and get into the BIOS?
I don’t understand? Could you repeat that but for a simple person like me
theyre saying after you update the bios are you able to get into the bios menu with the display connected to the motherboard, not a graphics card
Yes I can get to bios with the HDMI plugged into the motherboard. Am I supposed to plug it in to a graphics card when a card is plugged in?
configure your bios using the builtin hdmi. You don’t mine as well using the card’s hdmi.
See if you can get the gpu recognized by setting the bios for your motherboard
google something like setting bios mining maybe add your motherboard’s model
I plugged the HDMI to the card in the 16 slot and it worked. 
I was literally about to get a new board. Only picks up the card in the 16 slot and not the one on the riser. My last bonehead move has my thinking. Maybe I need to change how I have the riser hooked up?
I am thinking maybe I need to connect to that 6 pin instead of that flat part that is right next to it. I thought it was the same thing. Maybe not?
We’ll play with one card for now lol
