I’ll give -250 a shot.
Have tried -500 and -502 on core clock, very unstable for me, but I’ll try -250 core/ 1800 men and see if it will run.
With me, it seems if things aren’t right, the miner locks up, often requiring a hard reset at the rig, within a few minutes-I never get bad shares, just system lockup.
Will try and post any improvements if stable.
Looked good for a minute, but -250/1800 crashed on NBminer pretty quickly.
Invidia driver is good? 495.44 update and try again and this settings are for nbminer
Ok-I’ll try-I think I’m running 470.82. Which at some point seemed to be stable-I had some initial setup challenges, and tried some different drivers-these seemed stable, but that was before I started on Nbminer, so I’ll update and try new drivers with NB
Good suggestion-updated drivers-applied OC settings -250/1800 on all cards except my hot one-all around 40 MHS for a rig tots of 230 MHS-nice.
I’ll be able to push the cards a little more tomorrow after riser reconfig.
Cheers!
Anyone had any success with either of the following to increase hashrates?
Flashing MSI Gamer X card with Ventus Bios
I saw a weird overheat based technique where you warm them up, stop the fan for a couple seconds that unlocks high 40’s on these cards. Might give it a shot.
Gonna give Lolminer a try and see if any improvement.
Cheers.
And everything is good i hope.
Yes-thank you-stable for 32+ hours most hashing right about 40. On 5 of 6 GPUs
Risers delivered today-gonna split up my rig for better heat management and crank my 2 hot ones up.
Next stop-45 MHS.
I know this card will do 50, and I’m gonna keep working at it. Once everything is cool, I may try different core/mem clocks/power settings to see if I can get to 42-43.
I want to try the NBMiner overheat workaround, but I can’t seem to figure out how to implement it on 6 cards…need more data.
Same ve need to wait for next update.
OK-modded GPU rig setup, and rig is so much happier. It’s nightime where I live (Northern CA), and this time of year gets chilly, ambient temps in the high 40s F, low 50s F. Fans haven’t gone above 30% since the mod, and GPU temps 39-45 ish. I’ll see if the fans have to work a little harder in the afternoon when temps will likely be more like 70s F.
All said and done Breaking 3 cards off of my “Riserless” MoBo was the right play. Great thermal profile now.
Rigs have been stable overnight and being able to apply the same settings to all cards has my rig total up to just about 240 MHs.
I’m using NB Miner
Newest Nvidia Drivers
Current version of hive OS
OC set to
-250 core / 1800 mem - 140 pl
I’m happy with this hash rate. Will move into fine tuning mode.
Have been hyper focused on this for about a week now, since the upgrade cards arrived, so I might just let it mine for a few days and get back to some of the other projects I’ve neglected over the past week.
Will post updates if any progress on unlock hacks I try likely this weekend, although it’s my anniversary, so I’ll probably pay attention to that primarily (lessons learned my friends).
Try LOLMiner or T-Rex with:
Core 1600
PL 165
Mem start from 2800 to 2400 wait 2 or more hours and decrease by 16 until don’t have invalid shares.
45 for a lhr card is pretty cool. I have an old 3070 and it runs at 52 mhash stock 
Thanks brother-I’ll give it a try-would really like to see all over 40. I have like 2-3 that stay above 40, rest are around 38-39.
Will try your setting recommendations and report back.
Well-tried it from work and locked up my rig…d’oh.
I forgot my policy of only making OC mods when I’m Home…cause it frequently causes a lockup.
I need a wifi enabled power cycle relay-I’m gonna get one…
I am with Zotac rtx 3060 ti hynix mem. Initially worked well with 1200 core/ 1810 mem / 165 pl @ approx 42-43Mhs with nbminer 39.7. After adding next 2 cards all got messed up. Tried nbminer/t-rex. Rig kept crashing with LA going high to 20. Changed the slots / risers, and miner to gminer. Now Gradually going up with OC. Currently 1100 core / 1740 mem getting 38-39MHs. Will update once I cross 40Mhs stable… Nvidia driver is 470.74.
Awesome-thanks for the recommendation.
I have one consistently over 42MHs
All the rest are between 38-41 stable.
With the 6 cards, I get right about 240MHS.
Would love to find a sweet spot about 2-3 MHS higher on all of the sub 42 Mhs cards, but it’s pretty stable.
try core -500 mem 2200 pl 130 [HiveOS]
Getting 44.71 Mh on Palit GeForce RTX 3060 Ti
Samsung GDDR6
Driver 470.74
Miners to try (in order)
for me NBMiner is the most efficient
RVN is more profitable rn.
For RVN, I have CORE 100 MEM 1600 PL 160
Check out Sebs Channel for video guide
Thanks for the suggestion.
I got the Hynix…don’t think the settings will translate. I’ve had very little luck with -500 on the core.
