thanks for this!~
Hello, im newbie on mining. I have a this GPUGeForce RTX 2060 SUPER Dual 8GB GDDR6 (NE6206S018P2-1160A) and i have low h/ratę 36 on OC. Any solutions for this GPU?. My power limit its 100%
Which exactly are you trying?
Did you try BIOS for MSI Ventus ?
Actually i tried, inno 3d bios, because i have inno 3d card… I think the problem is my memory overclocks better when temps are low…and reduce its performance when temps are high…my card temps are 49-50…but may be memory are becoming hot…
Because heat sink is placed only on g
pu chip not on memory ( see image)
No, it’s not temp … It happens only on all algos similar to ethash. All other algos on this GPUs works fine.
Basically, it’s caused because on ethash algo GFX Core clocks too low to give you 40+ MH/s (725-900 MHz)
how to deal with this? , IF i increase m clock more than 820 then hashrates start falling.
i tried msi ventus bios but command propt, said pci substem id mismatch, so no changed applied.
This is understandable because the manufacturer’s identifier does not match and must be flashed forcibly with the forced flashing flag.
Another important thing is that you can get a non-working video card this way.
I am just adding my name to the list of people who can’t get this card over 38 MH/s.
Like @vulkan16 if I run the card at stock settings it draws 170W, but the second I do anything it drops to 100W, even if it’s moving the power from 100% to 99%.
I’m tempted to try what @hkuve2 did with the voltage, although I don’t know what to move on the curve and don’t want to mess it up.
I attached my settings if anyone has any ideas. I can increase power limit to 100 and it won’t change the watts or hashrate (it will still be 110W).
Try settings in my post: Low hashrate 2060 super - #48 by sourabh23 it might give you 40.32 [no need for any curve editing].
So I have 3 cards, 2 with Micron memory and 1 with Samsung. Identical “models” if you will except memory. Samsung hums along at 42Mh where Micron is stuck at the said 38. I tried downloading VBIOS in hive from the Samsung one and flash it to the Micron ones but every time I try downloading VBIOS HiveOS restarts… So here I am 
Wasn’t stable at those settings. Also I couldn’t change power level to 103 in Afterburner.
This is the most frustrating card I’ve worked with. Adjusting the Power limit changes nothing. Increasing/decreasing memory changes nothing.
Hello everyone, did anyone get any improvement on this kfa2/galax 2060s micron card? Here I have the same problem version bios 90.06.44.80.46, I had bricked the card when it flashed bios 90.06.44.00.AE, but I noticed, I was about to try the bios 90.06.44.C0.1D, but I’ve read here that someone use it and didn’t get 40+ mh/s… I’ve tried everything and the maximum I got was 38.4mh/s but I can’t get this value anymore… So this card really has a limiter eth?
Hello, I don’t know… I got improvements here, but with little problems, see with 190 pl what I got, but the consumption status and temperature don’t seem to hold up, with these parameters in the photo, there are times when consumption goes up for 160w and the temperature was almost 70º, and I don’t understand why. And also the LA 1min/5min is in red… maybe it’s not unstable. The worst thing is that with the PL below 190 I have the mh limited to 37-38 … it seems to be unsafe to use PL 190, does anyone use it?
I really don’t understand this 2060s card… after it was 70º I left the PL at 125… now I go up to 190 and it doesn’t go up in mh, watts, temperature, nothing responds
