Update drivers to latest, update hiveos to latest, try lolminer v1.33 and put your cc at 1400 (some cards like weird ones like 1350, some more 1420, I run 1400 works magic), start your mc at 2000, see how stable it is, then go down by 50 if not stable. PL at 130w, I have external fans to cool down rig so fan % is your choice. Try it, you should get stable 44-46mh, also first 5-10minutes dont change OC unless it crashes, it does some calibration process first minutes, then runs stable. Good luck, hope it helps (came to conclusion after much error and trial).
My 3060ti MSI ventus hynix , with driver 470.63 and Gminer 2.70 quite stable with this oc. been running more than 1 hour eth with 39-42MH
pudiste mejorar el power. me pasa lo mismo, pero no logro solucionarlo.
After moving that 3060ti Hynix Card to target rig (with mix of cards 2x 2070 2x 2060S 1x 3060 V1) and some additional tests I ended with:
41.99 MHs, LolMiner 1.34, N 470.74 driver and 0.6-210@211018-2 hiveOS
Core locked at 1350 MHz
Memory at +1600 MHz
PL without change, it is bouncing between 130-144W
CARD is Gainward RTX 3060Ti Ghost LHR
3 Likes
For Hynix …Core at 1600 mem at 1800 PL 165
Try out…
these setting worked for me perfectly, i am getting around 40.86 MH/s with 3060ti (hynix card).
the only thing i have observed is increase in power consumption for some extra Mh. I am coming from gminer and i used to get 38+ Mh/s (1400Core 1800Memory 130 PL)
I have a 3060 ti msi gaming x, it threw 34mh at most. Install a 3060 ti ventus lhr bios and now it outputs a stable 43mh @ 99w.
1 Like
Just share with you guys my EVGA FTW 3060TI with hynix.
I am using the latest NBMINER 39.6 which claims 74% unlock
I can see others can do 45mh on 3060ti, but i can only get around 43mh
Also the power consumption is much higher than cards with samsung
maybe could help them
in lolminer, with the following OC make them stable at 40 MH with 3060ti hynix (msi ventus 3x)
Hello,
With nbminer, you can try “lhr-mode”: “1”
However, even though it seems to work fine at lhr 74%, I noticed invalid share errors that I didn’t have before with driver 495.44. So, Think of upgrading the drivers only to 470.82.00.
Regard,
Jbsky
Update to NBminer 39.7, update drivers as well if you haven’t already - I’m using driver 495.44, and make sure you’ve updated your HiveOS. I have a few EVGA ftw3 ultra 3060 ti’s (LHR) with Hynix memory, and using the settings 1410 core, 2150 memory and no PL, I’m getting 44-45 mh per card. Been stable since the 39.7 update, no crashes. Each card ranges from 125-140 watts throughout the day but seem to stay around the 130~ range mostly.
1 Like
Thanks mate, i get 41.16mhs now and it’s stable. Cheers to you 
Good evening I have the same graphics card as
Core - 200 mem 1600 pl 145w
For a result of 42.5-43 mh with a temperature of 46° is the fan at 65%
An an update:
I change the core value since it was very hot temps on a core. So after changing it to 1400, power usage decreased and I get more cooler option. But I loose a couple mhs. But no problem at least its more efficient
Hello LINKIS, what arguments are you using on nbminer 39.7?
You mean command list?
If yes, nothing.
