these are for windows? i dont know how to put this with hiveos, maybe nvidia msi command?
has a chance that my rtx 3080 ti has some defect?
The only difference is that you double the memory in HiveOS.
So you would put 2400 for the memory value for the 3060 Ti.
Looks to me like you’re setting the 3080 ti to lhr mode 2, and then to 72%
I’d lose the “lhr-mode”: “2,1,1” command and set all the gpus to “lhr”: “75,75,75”
And I’d start the 80 ti mem at 2000, and try 1900 for a few minutes before you go the other way.
btw, my 3060ti is set at Core=1400, Mem= 2600, and PL at 135 (45+ mh)
my 3060’s are at Core=1500, Mem=2500, and Pl at 120 (36.4 mh)
Both with lhr set to 75%. I think the core being locked and it’s level has the most to do with setting off the lhr lock.
1 Like
Yep.
U can make a fine tune for every single LHR gpu by using this method. Key is locked core clock. If it is not, ur chance to get locked again increases because of high volatalite on mV which will drive miner to locked state again.
Also you may decrease the value once more by changing it until u see there is no “locked” state left.
After change your LHR% by increasing %0.1 and if u see u did not get locked nor decrease hashrate u may add another 0.1 to lhr.
Lock your cores and dont give them PL, they will find optimum mV by themselves.
and 2700 mem is too much. reduce it to 2.5k at the start and increase it 50 by 50 every 2 mins if you did not get locked.
2 Likes
in hiveos i just set the cclock and mclock, this is lock, i tried to put the cclorck and mclock command in T-rex but show a error that in Linux this command dont work
i dont know what to do =/ any config that i put, i get these LHR detect and hash of 3080 ti is around 48~55
i tried low mem clock and high mem clock, any clock gives me LHR detection =/ PL i put 350
thank you for 3060 ti and 3060 clock tips, increase the hash here <3
1 Like
hi ricardomok, would u try these settings which i sent you below first on 3080ti? if it can make with these settings, then u go upward step by step?
Hi dude, I lock my 3080ti core clock at 1300mhz on hiveos, however, the core clock has not been locked and it shows around 960-975 mhz in nbminer. So weird. And only 81mh.
Two Gigabyte 3080 Ti Eagle OC: constant 86 MH/s
How:
-
HiveOS version: 0.6-210@211024
-
Nvidia driver 470.74 (Linux)
-
NBminer 39.7
-
default command line arguments
-
Core: 1200
-
Memory: 2200
-
PL: 280
Have you ever tried 975 btw? if u didnt before do it and report what u have, i wonder it?
Start from 1065cclock and 2300mem. lhr 75 and reduce it 0.3 by 0.3, check every 5 mins. if you dont see any changes increase mem hz +50.
start over to this process again since you find a good spot between 2600-2800 mem then after u have to start your core clock speed.
if your acts trigger the lhr u have to go back and try to get to point from other way.
1- increasing or decreasing mem or core clock speeds
2- decrease heat of card somehow
3- increase or decrease PL
those are factors which are directly effective on hashrates. your multiplier is lhr. lhr must stay at %75 even more if u have chance to do.
Btw stay at %65 fan level it should be enough for a 3080ti or u may dont have enough space for 3080ti’s heat?
1 Like
I have exactly the same problem with my RTX 3080 ti Vision Gigabyte. I’ve done everything what you guys wrote and my hashrate still is ~70.
Guysss, thank you by all the tips, i just test the GPU with my PC and realize that the temperature was the problem. The videocard just reach 110 celsius on the fewer seconds and start the temp throlling problem. I just replace 3mm thermal pad from the back, and i could get 85 hash for some minutes, but then the GPU reach 110 celsius again and start lhr detection. i bought 2mm thermal pad to replace them and i think the gpu gonna be cool enough to mine again.
thank you for all time spend to help me solve my problem. i hope this thread help more ppls.
I got an issue with mine 3080Ti EVGA on tminer, it keeps fluctuating with hashrate and triggers LHR tune every 3-5mins. I have 3 other 3080Ti EVGA on the same rig, they’re hashing normally at 89-90mhs. Here’s the pic:
Can you help? Note that the card in question (GPU2) triggers LHR few times quickly at the start of mining/booting.
Check throttling?
fwiw: my 3080TIs prefer much lower memory values.