yes i only get 8-9mh so i dont use cmode. using 20.40 drivers
Wow, something must be set incorrectly.
Заметил очень сданную особенность. Когда проверял карты по 1 шт они выдавали по 102 хэша. как собрал их в кучу некоторые 99,56 стали выдавать некоторые 101 некоторые 100,1… память hynix на всех…
настройки на всех одинаковые
1675
950/0/0
1125
amdmemtweak --RC 38 --RP 13 --FAW 12 --RAS 25 --REF 7500 --RTP 6 --RRDS 3 --RCDRD 13
подскажите с чем это связано?
While I don’t have the answer for you @TESLA78 , I see some GPU performance variation between single GPU, in rigs, and even dependencies among slots in rigs. These are all riserless examples.
Can only speculate some of it is related to the chipsets, load balancing of work, etc. Wish I knew 
Tweaking a Hynix Memory VII down a notch?
I have one GPU in a multi VII rig which will “choke” in TeamRedMiner after a few hours running with the baseline amdmemtweak below:
“/hive/sbin/amdmemtweak --i 0 --ref 7500 --rtp 6 --rrds 3 --faw 12 --ras 19 --rc 30 --rcdrd 11 --rp 11”
Any suggestions on which settings would be best to try and back down a notch?
Note: running this as baseline across all my air cooled cards and 10bit is successfully enabled:
“In HiveOS make sure your overclocks are 1600 Core @900mv and max 1000 mem clock.”
double-check the test file its prob an extra " some here or missing one.
Did you manage to solve it?
198 did not work for me i had to got to 195.
c mode should automatically on when 10bit is enabled.
Hi. Where to enable 10bit? I always get error, when i try Radeon VII C-MODE GUIDE!** tnx
i did once, its got to do with the hiveos version not all versions will allow c mode for these cards, i am back to B mode.
Ok, tnx. And which version of HiveOs is that?
Cant update-grub2 keeps saying syntax error line 54
just got it working, after to do the text file update you need to run the update-grub2
command and then reboot and it should just come up in cmode, the version i am using is 5.4.0-hiveos · H 0.6-198 · A 20.40
can i install a radeon vii along with other nvidia cards?
You can.
It will require you to have a specific plan on miner choices, specific limiters in advanced miner configs per – “GPU”, etc.
For me, it is not worth the effort of maintaining through OS, Miner, environmental adjustments, etc.
i configured the flight sheet for the radeon but i can’t get it to go at 100mh.
I followed the guide of redpanda (Enabled the 10bit and changed the timings), but I don’t reach 100mh
the only doubt i have, is in the timing string where i may not have guessed id gpu which should be 6 or 0?
this is my card
Is it running 90-91? It looks like the “10 bit” was enabled.
Mixed rig GPU id’s are tough. Does the miner present a full list that maps to your expectations? Where are you getting “6”?
Not sure if the mixed rig counts are in play for amd tweaks. My mixed amd only rigs with RX4/5s, 6800s, and VIIs did not count the internals and began with 0, 1, etc.
Have you tried 0 or 1 yet since there is only 1 AMD card in the list?
I have not tried this with mixed rigs, only in AMD only rigs 
hello nice to meet you @Fribbes
I got 10bit block size now. but i watch hive shell. its still use b mobe
can you help me ? 