NBMiner update unlocks up to 70% of NVIDIA RTX 30 LHR series mining

[gunzen]

Hey, I mine ERGO with a MSI 3060 Ti LHR with Hynix, too. My Problem under NBMiner is, that the card will just throw between 77 and 80 MH/s. Directly after startup it does 155 MH/s , one minute later 124 MH/s and again one minute later it’s with 77 MH/s (look screenshots).
After nearly 15 minutes (!) the 3060 Ti goes at ~138 MH/s which is nearly perfect for this configuration. In my second rig are one 2070, one 3070 Non-LHR and two other 3060 Ti LHR which don’t have these problems…

Screenshot at 08:16 AM this morning:

Screenshot at 08:17 AM:

…and again one minute later at 08:18 AM:

Finally at 08:29 AM it reaches suddenly its normal setting:

[deusofpower]

That 3070 Ti is drawing a whole lot of energy. 200 Watts for 54Mh/s is not very efficient. Can you lower that to let’s say 130-140 watt without losing hashrate?

[ohyala]

I had try to mine ERG before,

But It is not stable, sometime it will cause crash,

The sweet spot to avoid trigger LHR system is hard to find.

Therefore I move to mine RVN.

[gunzen]

Maybe the MSI cards have to drive warm before unfolding the full power…
Until this special “error” with this special MSI card my rigs are running wonderful mining ERGO. For me personally RVN uses to much energy, somehow not efficient.

[BOOOOM]

Nope, 3070 Ti is power hungry…

[BOOOOM]

Theres no special settings.
OC is at picture and NBminer LHR unlock just works

[diego-ar]

[msjavid77]

hello everyone ,
3080 evga is LHR but work with nbminer . tnx NBminer

[AmitP77]

Thanks for reply I will try those hope will work for me as well.

[rkwjunior]

That’s an LHR 3080, no way. Show me the box ot came out of.
Do me a favor
Go to 1080 core and 2150 memory. I want to see if you get 99 mh.
Which evga. ftw3 or xc?

[greenmeanie]

It seems to me NBMiner is slower to the payout compared to gminer or lolminer even with the faster LHR hashrates.

[rkwjunior]

Miners dont payout, the pools do.

[elonmonkey]

Hello, I am a newbie with mining. i have setyup mining with a 3070 and 3060ti LHR. currently i am getting 59, 38 MH with lhr 68 settings(default) on nbminer.

where can i modify the value of lhr in hiveOs, is it in flightsheet data or OC settings

[rutra]

Miner config/ extra arguments:
“lhr” : “68”

[gadget069]

I’ve tried using nbminer and my lhr v1 cards “nerfed” will not get over 26 mh/s. What driver is everyone using?

[rutra]

460.91.03
3060ti lhr 38-41mh
3070 lhr 42mh
What setting do u use

[gadget069]

I’ve tried every drive in the book and cannot get them to work on nbminer. Currently using lolminer, 460.39 getting 37.5 mh/s on my 2 3060 v1 lhr cards

I also get this error when adding the lhr setting

[onzi]

Hi,
You have to remove any Extra config parameters

Version 39.2 assume parameters itself.
Regards

[gadget069]

That’s what I thought.

[Phamtastic-Miner]

You’re right, 3070 ti is power hog but i was able to reduce the 185 watt and keeping it around 54-55 mh/s.