Dont buy the MSi cards. Get the evga. Much better gpu.
You mean the model XC3 ULTRA GAMING?
No, ftw3 ultra
Your temps aren’t bad. Your running fine.
Didnt know u could use team redminer for Nvidia gpu?
But id set the Auto fan up to 50c. Then set the fan to 0, that way you dont have to worry about it.
Thank you for updating me 
I have tried, you were right, I was wrong. So my next question: Is absolute core clock applicable for mining each and every coin?
Hey, just here to help. I just wish HiveOs made it more well known to everyone.
How much power did you save?
I know it works for Ergo. No sure about anything else.
Rick
I’m only running one rig 8xRTX3070 so in terms of power I saved around 30 Watts which still is good, every little helps. I have the rig set up in a really warm ambient environment so going down to 55 requires me to use air conditioning as well. Also, what are your settings for ERGO which I’m guessing is next line? And how long have you been mining on your RTX’s 3070, what would you say safe memory OC is? Thanks for your reply, regards
Actually I’m wrong about Ergo, i saw a video on 3080s on YouTube for Ergo and they used absolute core. I tried it myself for only one day and i used regular core clocks, it seemed to like regular cores in my short experience. id have to try it again.
As far as memory settings i used windows to benchmark and watch memory junction temps, then used same settings on Hive. I found that even 2700 was safe, The 3070s stay pretty cool.
But on Trex i have mine at 2575 at 62.2 MH
Gminer i use 2625. 62.2MH.
Ive only been mining for 3 months
I am using Trex for Nvidia and Team Red miner for AMD.
Using fan 0 and set core temp to 50. Will check out if it works.
Dude to my knowledge the OCs does not depend on the miner or the algorithm, i mean Absolute clock or not , the OC is set by the related OC application. than the GPU starts working with the set OC settings and then you run miners. Atleast for my AMD is like this. For Egro i think you can use your current settings and you can get double the MH/s you get with Eth.
Amds i have no idea, but for nvidia i absolutly have to change my overclocks. I will demonstrate it if ud like. I literally just did it the other day.
Pheonix miner also gave me the most invalids.
When it comes to Ergo, my eth settings do not work, i have to use regular core settings and much lower memory, and lower powee limit.
Yes it is more than double the hash rates and much lower watts depending on Gpu.
My 3080 gets 213 mh at 180 watts, -502 core, 1550 memory on Ergo nanominer.
Absolute core did not yield good hash rates and it ran warmer. I did this yesterday
very strange. for my AMD my settings worked as the ETH but i needed to adjust as you say the memory because for autolykos i think is more valuable the GPU core and memory clock. so a tweak is needed to increase a bit teh clock and to reduce the memory
Ya, i have to raise my memory by 75 or 100 if I go from trex to gminer to maintain hashrates
even more than double;
RTX3070 mining ETH: (absolute core clock 1100) + (mem 2400) + (fan 0) + (PL 0) = 61,59 Mh/s
RTX3070 mining ERGO: (core clock -500) + (mem 2400) + (fan 0) + (PL 125) = 169 Mh/s
bon chance!
Thats about right for me.
My best on ergo was 165Mh at 110 watts.
I do like how ut runs cooler also
I’m not suggesting anything; I only was replying to previous post which said that you get double the hashrate on ergo than on eth; and I only said it was more than double.
Its more than doube for your card. The 3070 does 30% more. There are other cards like this also but not all. Usually other cards do double of the ETH hash rate when mining Ergo.
This topic was automatically closed 416 days after the last reply. New replies are no longer allowed.