Rig won’t start mining even after reflashing the image. ‘GPU driver error’ kept popping out and starting hive shell will give out ‘hssh start (failed exitcode=1)’. Rig was running fine with 1 x 3080. After adding 1 x 3070 Ti, the rig won’t start mining. Any response is greatly appreciated.
lower OCs and try again, driver error is typically from too aggressive OCs, but can be from faulty power cables/loose cables/cards etc.
It says
GPU Health Data:
Latest GPU driver errors list:
Feb 06 23:30:47 Rig_No_1 kernel: NVRM: Xid (PCI:0000:02:00): 62, pid=’’, name=, 0000(0000) 00000000 00000000
Feb 06 23:30:47 Rig_No_1 kernel: NVRM: Xid (PCI:0000:02:00): 45, pid=6998, name=t-rex, Ch 00000010
Which GPU is causing the issue?
Look on the left side of your gpus on the worker overview screen and you will see the pcie bus locations. Match to the one in your error, if the screenshot is from the same rig above it looks like your integrate graphics is causing issues for some reason. You can disable it in the bios and see if it helps
How about these errors?
GPU Health Data:
Latest GPU driver errors list:
Feb 06 22:33:58 Rig_No_1 kernel: NVRM: Xid (PCI:0000:02:00): 62, pid=’’, name=, 0000(0000) 00000000 00000000
Feb 06 22:33:58 Rig_No_1 kernel: NVRM: Xid (PCI:0000:02:00): 45, pid=7014, name=t-rex, Ch 00000010
GPU Health Data:
Latest GPU driver errors list:
Feb 05 22:18:20 Rig_No_1 kernel: NVRM: Xid (PCI:0000:05:00): 62, pid=’’, name=, 0000(0000) 00000000 00000000
Feb 05 22:18:20 Rig_No_1 kernel: NVRM: Xid (PCI:0000:05:00): 45, pid=10096, name=t-rex, Ch 00000010
Are they related to the integrated graphics?
You can match the number after PCI to the pcie bus location next to the device on your workers dashboard to se which error is for which device
I’m having the same problem, nvidia errors after boot.
Have you flashed the latest stable image on a known good drive?
Does the gpu work?
What gpu and what settings?
The boot stops in the nvidia driver and the rig goes off line, after 10 min the miner don’t start and it shows the same errors in this thread. Some times it’s work until another reboot and the same prloblems again. I’ve tried hive-replace and a some nvidia drivers.
Can you post a screenshot of your workers overview tab?
Now it’s working, I don’t know what is happen.
Test the problem card on its own, make sure risers/cables/pus etc are all working.
It was working, I tried to change the flightsheet and it goes offline. I made a lot of reboots but every time gave me a random error.
Test the card on its own, make sure everything is working
The card and all others was working, until I changed the flight sheet.
Alright, test the problem card on its own, with changing flight sheets. Rule out all variables such as loose cables. Faulty risers, bad slots, faulty psi’s etc.
The problem is not that card at all, every card that I put in the rig gave me the same random errors. After lots of reboot it work, this cycles keeps going with all cards.
The problem could be the card, riser, cables, psu, pcie slot to name a few. The problem is not changing flight sheets. If you do not do basic troubleshooting you won’t know what the actual problem is.