i cant faind it
Hi do you repair your problem?
Hi there
Did you have to do something to make it work.
With me hiveos finds for example 2 Amd or 2 Nvidia cards but afterwards only the card in pcie1 works.
It says only one openCl card found
Cheers
All I did was update the bios, and then run HiveOS no problems.
I just updated today in it ran good on slot 1 and 2, but not the rest.
at bios start slots 3 and 4 are “red”
I wrote to Asrock as well…
Have you setup the bios correctly ?
Have you enabled " Above 4 G " in Bios ?
I am having similar issues, I am running the Asrock H510 and I can only get 1 GPU to work at a time. HiveOS say use PCI link speed Gen 2, not tried Gen 1 but may try this tomorrow. Any other ideas? Do I need to add a M.2 drive to this board for it to mine with >1 GPU? I have 1 x Nvidia 3060 XT to and 2 x Radeon 6600 XT AMD. Hiveos engineer said:
Try to check your bios settings
PCIe Link Speed = Gen2
4G Decoding = Enabled
CSM Support = Disabled
you need to upgrade bios and it should be ok
Hello! I cant get to work with 5 cards… Already set gen 1 to all pcie speeds… what is wrong?
Configure BIOS, 100% is a problem in bios , try configure bios…then it will work.
Bios update is a must. I have two of these boards each running 11 cards with i3 10100 cpu’s (no internal gpu), stable as anything. Just make sure your power the different molex’s of the correct psu for the gpu
I have all 6 gpus working for all the 6 slots, my question is how to make the 7th gpu via the mining port work?
I have a gpu riser and usb cable connected to the board powered by a PCIE using a Y-splitter. Miner will crash everytime I plug in the 7th gpu. Any thoughts? TIA
If you connect HDMI on the Onboard Graphic, is it normal when Hive OS Boots? or blank screens. in Me When Booting to HiveOS the screen is blank continuously.
1 Like
Having this same issue with ym ASRock H510 pto-btc +. Only “A” slot (slot 0 and slot 1) will show green and run, all others slots will be “red” and show error. I have most recent bios update for mobo and hiveos is UTD as well. CSM support disabled, above 4G enabled, all PCIE speeds set to Gen2. All HiveOS recommended mobo settings set as described in HiveOS new user guide.
My cards are rtx 3090, rtx 3060 lhr, and AMD 6800xt. All cards work great when solo.
Only using one atx PSU atm (1600W), all cards hooked directly into pcie slots (no risers etc)
Anyone know what else I can try? Thanks in advance
Have you installed additional power on the mainboard? I’ve been like that before, then I put the power on the mobo, the PCI-E status is green, all when plugged in the Graphic Card
1 Like
Your exactly right … Whenever I plug into the onboard HDMI port I get no display and no boot Up of Hive OS as soon as I plug HDMI into the main graphics card closest to the CPU the system boots perfectly and runs HIVE OS and I’m able to mine. If there is a fix for this out there please post and again thank you for your post.
Hi
I’m New to mining.
I did set up all GPU to GEN1 and enable 4g Decoding
but only 1 GPU is mining
updated driver of GPUs to 470.63.01
any idea what else to check ?
This fixed my issue. I didn’t have the additional power hookups plugged in on the mobo, just the main one. Thanks!
Hey there, just checking to see if you found a resolution. I have the same board, with the Intel i5-11400. I don’t have any external GPUs right now, so I am trying to use the integrated video. Result is the same, no boot and blank screen.
I cannot access the BIOS at all on the ASROCK H510 Pro BTC+ that I just purchased. I get the 5 beeps and I just get a black screen when connecting the HDMI to the MOBO. But when connecting an HDMI cable to one GPU it shows Hive OS and it is mining, but only on one card, no matter which one I plug in. Also, I am using an SSD hard drive connected to the Sata connector.
I have reset the CMOS, taken the battery out for 15 minutes, and put it back in. Have rebooted and reset the mobo several times and am still not able to access the BIOS! Please help.