WiFi setup

Sirius_x · January 4, 2018, 11:18am

Спасибо за подсказку
Только немного в другом месте изменил настройки.
Свисток TP-Link TL-WN823N.
Не подхватывался при старте.
По команде WIFI запускался.
В директории etc/network/ файл interfaces немного подкорректировал.
Прописал своего wlan0 и добавил значения wpa - ssid и wpa - PSK
Все завелось !
Глядишь кому и понадобится

Polkovnik · January 7, 2018, 10:03pm

Спасибо, помог!

sk1zo · January 14, 2018, 1:26pm

Hi, hiveos is amazing! But i can’t made work my TL-WN821N V6 http://www.tp-link.com.au/download/TL-WN821N.html.

root@rig:~# lsusb
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 2357:0107
Bus 001 Device 003: ID 046d:c22d Logitech, Inc. G510 Gaming Keyboard
Bus 001 Device 002: ID 046d:c05b Logitech, Inc. M-U0004 810-001317 [B110 Optical USB Mouse]
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

This Bus 001 Device 004: ID 2357:0107 is tl-wn821n.

I handle it in lubuntu 16.04 with:

sudo apt-get install build-essential linux-headers-generic dkms git
git clone https://github.com/Mange/rtl8192eu-linux-driver.git
sudo dkms add ./rtl8192eu-linux-driver
sudo dkms install rtl8192eu/1.0

But in hiveos apt-get install fail:

Setting up linux-headers-4.4.0-109 (4.4.0-109.132) …
Setting up linux-headers-4.4.0-109-generic (4.4.0-109.132) …
Examining /etc/kernel/header_postinst.d.
run-parts: executing /etc/kernel/header_postinst.d/dkms 4.4.0-109-generic /boot/vmlinuz-4.4.0-109-generic
: Unable to find an initial ram disk that I know how to handle.
Will not try to make an initrd.
Setting up linux-headers-generic (4.4.0.109.114) …
root@rig:~#

I can install driver anyway and then adapter wlan appear in iwconfig, but can’t assosiate with my router.

root@rig:~# iwconfig
wlan0 unassociated Nickname:“WIFI@REALTEK”
Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated
Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

eth0 no wireless extensions.

lo no wireless extensions.

I try hiveos wifi setup but not work for TL-WN821N V6.

kernel log:

Jan 14 14:02:05 rig kernel: [ 611.642398] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=7c:8b:ca:05:c8:2f
Jan 14 14:02:05 rig kernel: [ 611.643915] usbcore: registered new interface driver rtl8192eu
Jan 14 14:02:05 rig kernel: [ 611.643917] RTL871X: module init ret=0
Jan 14 14:02:06 rig kernel: [ 613.135724] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jan 14 14:02:08 rig kernel: [ 615.137167] RTL871X: nolinked power save enter
Jan 14 14:05:30 rig kernel: [ 816.863657] RTL871X: nolinked power save leave
Jan 14 14:05:32 rig kernel: [ 818.285198] RTL871X: nolinked power save enter
Jan 14 14:05:38 rig kernel: [ 824.772178] RTL871X: nolinked power save leave
Jan 14 14:05:39 rig kernel: [ 826.189118] RTL871X: nolinked power save enter

Thanks!

mungiu · January 23, 2018, 5:21pm

Detected bug:

1 - Flashed fresh image to USB (16GB usb3.0)
2 - On first boot everything is ok, connected to wifi via “wifi” + credentials
3 - did a “sudo reboot”
4 - “wifi” + credentials will not connect anymore

Anybody knows why? I will try to replicate this again if it continues will post down.

Currently:
1 - flashing HiveOS to USB again.

mungiu · January 23, 2018, 7:36pm

Sorry for the double post, I can confirm wifi setup runs the first time only. If the system reboots, or shuts down or crashes “wifi” command with credentials will not work again.
Would be happy to switch all of my rigs to Linux using HiveOS if this could be solved. Thank you, Devs for all the work you already did, will donate if this gets solved.

sk1zo · January 29, 2018, 6:58pm

I can made work wifi without wifi setup, but i have same issue than mungiu, when system reboot wifi not connect.

root@rig:/hive-config/network# wpa_supplicant -c /etc/wpa_supplicant/wpa_supplicant.conf -i wlan0

Successfully initialized wpa_supplicant

wlan0: CTRL-EVENT-SCAN-FAILED ret=-16 retry=1
wlan0: CTRL-EVENT-SCAN-FAILED ret=-16 retry=1
wlan0: CTRL-EVENT-SCAN-FAILED ret=-16 retry=1
wlan0: CTRL-EVENT-SCAN-FAILED ret=-16 retry=1
wlan0: CTRL-EVENT-SCAN-FAILED ret=-16 retry=1
wlan0: CTRL-EVENT-SCAN-FAILED ret=-16 retry=1
wlan0: CTRL-EVENT-SCAN-FAILED ret=-16 retry=1

o08 · January 29, 2018, 10:34pm

[quote=“DimaFern;53”]These devices fully work:

148f:7601 Ralink Technology, Corp. MT7601U Wireless Adapter
7392:7811 Edimax Technology Co., Ltd EW-7811Un 802.11n Wireless Adapter Realtek RTL8188CUS

DOES NOT WORK: TP-LINK TL-WN725N works with options described in comment below.

[/quote]

MT7601U
DOES NOT WORK
Please help!

o08 · February 2, 2018, 3:12pm

MT7601U is https://ru.aliexpress.com/item/Mini-USB-WiFi-Adapter-N-802-11-b-g-n-Wi-Fi-Dongle-High-Gain-150Mbps/32819666725.html

Rusik · February 6, 2018, 9:20am

TP-LINK TL-WN822N tested and working - better than small usb adapters (two anttenas and long USB cable)
wifi command runned and to be sure just added following lines in /etc/network/interfaces

auto wlan0
iface wlan0 inet dhcp

mrhot2000 · February 12, 2018, 12:10am

What to do?

Rootless · February 12, 2018, 12:51pm

try a different network adapter.

o08 · February 14, 2018, 5:46pm

in hiveos version 0.5-30 MT7601U works!

Psiheya · February 18, 2018, 3:12am

Not working for me.

injoy · February 19, 2018, 4:30pm

Отлично работал вайфай пока не полез настраивать чтобы он сам поднимался после перезагрузки.
Настраивал в директории etc/network/ файл interfaces и случайно сохранил пустой файл. Возможно после этого вайфай перестал работать. Поделитесь кто-нить кодом который в файле прописан по умолчанию.

snovik · February 24, 2018, 10:16am

В арче все подхватывается без проблем. В hive кернел сыплет device descriptor read error. Т.е. не вопрос линукса, а проблема в сборке hive. В какую сторону покопать?

Realtek Semiconductor Corp. RTL8192EU 802.11b/g/n WLAN Adapter

pducharme · March 19, 2018, 5:29pm

Hi,

Just moved to HiveOS. Very nice OS! My only issue is with Realtek RTL8811AU 802.11ac USB 2.0 That is not recognize by HIVEOS when i do the wifi command, it say “No wlan0 interface found”. I ran the “lsusb” but its not clear if the Realtek listed there is the onboard NIC or the USB wifi dongle.

What should i do to make it work? Thanks!

pducharme · March 20, 2018, 2:48am

Replying to myself, here is what I did to make it work

sudo apt purge rtl8812au-dkms
sudo apt install git
git clone https://github.com/gnab/rtl8812au.git
sudo cp -r rtl8812au  /usr/src/rtl8812au-4.2.2
sudo dkms add -m rtl8812au -v 4.2.2
sudo dkms build -m rtl8812au -v 4.2.2
sudo dkms install -m rtl8812au -v 4.2.2

after that, I just ran the “wifi” command and the adapter was found. I entered my ssid, password, and it connected. It wrote config. Then, I rebooted without Ethernet plugged in, and it auto-connected

cremator · March 23, 2018, 7:41pm

А если на WIFI нет пароля, что делать? Если его просто пропустить, то пишет Empty value и опять его требует.

Monarx88 · April 6, 2018, 7:51am

Знающие люди, помогите пожалуйста. Тоже проблема с вайфаем, ссид и пароль не запоминает, приходиться вводить каждый раз после перезагрузки. Видел что советовали отредактировать файл /etc/network/interfaces, так вот, как до него добраться и отредактировать? Пробовал через sftp в тотал комадире, но там не дает его сохранить после редактирования.

HellRazor · April 26, 2018, 3:54pm

How can I disable wifi after it has been setup? When I type “wifi” it only asks for IP address etc but there is no option to disable wifi.