I have these on 56 sapphire hynix, mem 965 core 1030 vdd 835
straps
amdmemtweak --CL 20 --RC 37 --RP 11 --WR 14 --CWL 8 --FAW 12 --RAS 20 --REF 65535 --RFC 248 --RTP 5 --RRDL 6 --RRDS 3 --WTRL 9 --WTRS 4 --RCDRD 12 --RCDWR 12
hash 53
1 Like
Hey mate,
Thx but still nothing just detect dead on GPU5
But i have 3x
Radeon RX Vega 56 8176 MB · Sapphire
Hynix HBM2 · 113-D0500310-S01
and 3x
Radeon RX Vega 56 8176 MB · Sapphire
Hynix HBM2 · 113-376XL-U43
There could be a problem ?
with an hour of execution
straps amdmemtweak --CL 20 --RC 37 --RP 11 --WR 14 --CWL 8 --FAW 12 --RAS 20 --REF 65535 --RFC 248 --RTP 5 --RRDL 6 --RRDS 3 --WTRL 9 --WTRS 4 --RCDRD 12 --RCDWR 12
1 Like
I actually just sold that Vega, like the day I got it to 98 watts, but got 2.13 LTC for it which has done well the past couple days I did write down the strap through!
amdmemtweak --CL 21 --RC 36 --RP 13 --WR 13 --CWL 7 --FAW 12 --RAS 23 --REF 65535 --RFC 248 --RTP 6 --RRDL 5 --RRDS 3 --WTRL 9 --WTRS 4 --RCDRD 20 --RCDWR 14
These are very conservative straps if you have any issue with this bump RC to 37 first.
1 Like
Hi there,
I’m totally new to Hive OS and this forum 
Yesterday i installed Hive OS on my 3 GPU mining rig. Unfortunately my 3 Vega 56 GPUs are Gigabyte ones with Hynix. I’m tweaking around since yesterday. Using TeamRedMiner and AutoFan settings of Hive OS.
Where should i start tweaking and overclocking?
I’m not unhappy with my 45 Mh/s but I’m unhappy with the power consumption and a little bit concerned about the temperature.
Again for Gigabyte 56 Hynix owners:
amdmemtweak --CL 18 --RC 34 --RP 12 --WR 13 --CWL 6 --FAW 12 --RAS 22 --REF 65353 --RFC 164 --RTP 4 --RRDL 5 --RRDS 3 --WTRL 9 --WTRS 4 --RCDRD 12 --RCDWR 4
But I assume not every card can run with these settings
1 Like
You won’t do anything more with power consumption but I wonder what wattmeter would show, if it’s the real difference comparing to other manufacturers from the wall or it’s only wrong HiveOS value. I didn’t check it, I don’t have the card anymore.
Failed to initialize with these Tweaks.
Any suggestion which parameter to “fine tune” / change?
Rise RC to 38 and RCDRD to 18 and if it runs fine lower one by one every 15-30min.
its new TRM vers. with enhanced gpu detection… 
I rolled back to TRM 0.8.0 and no issues since…might be too high oc on some gpu tho…
Mem 965 is way to high for Hynix, start with 930 and rise every 5mhz
Nice good to see MH like this without falling .
My Vega 56 Samsung running nice and stable as well …
But in Hynix rig i had one problem with one GPU showing “got incorrect temperature 511, ignore”
so i removed it and now mining is stable but still LOW MH but better than nothing.
Back to “got incorrect temperature 511, ignore” - i want to change PCI Express extender for new one … or is there anything else ? Anyone have same issue like me ? Cables from PSU are okay.
Lucky you are, my Hynix are running 925 and 945. Don’t you have invalids?
good point … 
–CL seems to be a problem for my card. Everything below --CL 21 leads to an error.
Anything ideas?
no invalids, i get some on high cre Samsung… but its 1 2 now and then. these are solid
I had this issue when one power cable burned itself and also when I had problem with external fan which made some noise in electricity. You should check your electric devices.
1 Like
You can set CL 20+, this shouldn’t affect your hashrate
Thanks. Are RC and RCDRD the most important values concerning hashrate?
Does any of the Tweaks directly affect power consumption?