RTX 3060 Model 2504 (aka LHR v2) HiveOS Hashrate Limit's

[ob812]

@tlsolutions

I suggest lowering the PL on your 3060’s to 103, why would you want to use more power then needed? This is not a perfomance race, where you use nitrogen cooling to overclock stuff. Be more thoughtful, gaining 1.5-3% performance increase for 10-20% power cost increase is a no-no. Here is the example:

I see you have installed the 460.39 drivers, whenever I try I get the error that hiveos no longer boots, how did you do that you can use the drivers?

[tlsolutions]

If it won’t boot after installing 460.39, then atleast one of your GPUs is a rev2 LHR card.

Nvidia released 460.39 in jan. 21 and rev2 LHR card support was added later this year, around june. This is why it won’t boot up with 460.39.

[ob812]

howe I can finde out wich one is LHR1 and LHR2?

[tlsolutions]

Ti GPUs are all LHR cards

for the others, here is a reddit post:

r/nvidia - [Guide] How to distinguish between LHR and FHR variant of RTX 3000...

don’t forget to upvote

[eviltim]

[tlsolutions]

Are you sure, that this is not a nonLHR card? Those are supposed to do 45 MH/s

If this OC is stable atleast for 24h then it’s ok, but 170 watts is a bit too much

[dr.manhattan]

170 watt ???

[youallmine21]

try these for 3060 zotac LHR twin edge OC

[youallmine21]

ergo coin or eth?

[Vamsi]

Unable to install 470.86.

During install rig is disconnecting, what to do?

[iannmac]

wait, after upgrade driver to 470.86… miner always had a problem.
GPU not detected. and need to reboot… every 1 hour. any solution ?
OC is not higher .
im using NBminer 39.6 .
im trying NBminer 39.7 and get error " Nvidia setting applied with error . " GPU clocks 1500mhz not supported. " .
before error nvidia setting, "error no temp "

[xandi8207]

try this:

• stop the miner
• reinstall nvidia driver to the latest version
• update nbminer to latest version 40.1
• restart rig
• stop miner
• run this command: apt install --reinstall -y nvidia-settings
• restart rig

See if it works out…
Source: https://hiveos.farm/guides-driver_upd/

[sepheronx]

I got two gigabyte RTX 3060’s that wont go above 26MHs

using Gminer 2.72. Any advice?

edit: I noticed on the rig itself it says LHR - N/A for those two cards.

Edit 2: I updated to 2.73 and it seems to work now. Issue is, I noticed on the Rig, it said DAG damaged, check OC for GPU 3. I am unsure what OC settings to use at this point.

[iannmac]

ok i will try. thanks for advice

[cemko28]

i use lol miner.

[scholtzbros]

I know it’s a bit wild.

I use T-Rex miner LHR 75% and it’s stable so far (40 mins).

This picture shows a peak value, the total hasrate is ~ 97,5-100 MH/s

[iannmac]

im tryubg command : apt install --reinstall -y nvidia-settings
and new problem … confusing

[azmud]

these are the settings im running with, and have been stable for 7days

[Billybob]

I am new to mining and have my 3060 PL set to 150 W. I get 40.7MH and the temp is 46 degrees and is stable for ~2 months. I thought if the temp is low enough (i.e. <50) then I am not damaging anything. Is this correct?